This Chevrolet Corvette C8 installation resource page includes the official Vertical Doors, Inc. installation instructions, technical videos, fender removal information, wiring modification guidance, shock installation tips, fender bracket instructions, and final adjustment procedures.
These resources are intended to help professional installers correctly install the Vertical Doors, Inc. Vertical Door Conversion Kit on compatible Chevrolet Corvette C8 models.
Important installation notice: Read the complete installation instructions before beginning. Proper vehicle support, alignment, wiring protection, hardware installation, and clearance inspections are essential. Installation should be performed by an experienced automotive technician.
1. Official Chevrolet Corvette C8 Installation Instructions
Review the complete Vertical Doors, Inc. Chevrolet Corvette C8 installation manual before disassembling the vehicle or removing the original door hinges.
Corvette C8 Model Years and Installation Details
Use the model years listed below for current Corvette C8 Vertical Door Conversion Kit applications.
Model
Model Years
Stingray
2020-2027
Z06
2023-2027
E-Ray
2024-2026
ZR1
2025-2027
ZR1X
2026-2027
Grand Sport
2027
Grand Sport X
2027
The Z06, E-Ray, ZR1, ZR1X, Grand Sport, and Grand Sport X follow the same general installation procedure as the Stingray, with minor differences. Contact Vertical Doors, Inc. before installation for the details specific to your model and kit.
Call 951-245-8669 or email sales@verticaldoors.com. Have your Corvette's model, model year, and kit part number ready so we can help with the correct installation details.
The Corvette C8 installation requires extending three wires on the driver side and two wires on the passenger side. Protect every connection and route the wiring so it does not stretch, pinch, rub, or interfere with the hinge during the complete door movement.
6. Chevrolet Corvette C8 Shock Installation
This video explains how to install the gas shock on the Chevrolet Corvette C8 Vertical Doors, Inc. hinge assembly.
7. Tech Tip: Greasing the Shock Spherical Ball Bearing
Properly lubricating the spherical ball bearing helps the shock move freely as the door travels outward and upward. Follow this technical tip during installation and shock service.
8. How to Adjust the Horizontal Door Movement
The door must move outward through the correct horizontal travel before it is lifted. This adjustment helps provide proper body clearance and controlled vertical movement on the Chevrolet Corvette C8.
9. Avoid Common Lambo Door Installation Errors
Watch this video before completing the installation. It covers issues that can affect door alignment, body clearance, wiring, hardware, and overall operation.
10. Additional Chevrolet Corvette C8 Installation Video
This additional Corvette C8 installation video was created by Kano Kustoms .
11. VDI Shock Installation and Warranty Protection
A VDI gas shock normally cannot be compressed by hand. Shock pressure depends on the vehicle application. The shock is designed to work after the correct hinge is mounted to the vehicle and the shock is installed in the specified orientation. Never improvise a compression method or clamp the shock body or shaft.
Grease, threadlocker, and shock warranty requirements
Follow Steps 1 through 5 in order. Complete the grease and threadlocker preparation before threading the shoulder bolt into the hinge.
Grease the smooth body of the shoulder bolt. Keep grease off the threads.
Grease the shock-end contact surfaces shown in the current instructions. Complete this step before threading the shoulder bolt into the hinge.
Insert the shoulder bolt through the top shock end before applying threadlocker. Make sure the underside contact surface of the shock end is greased. Remove any grease from the shoulder-bolt threads, then apply liquid red threadlocker to the clean threads. This order helps prevent grease from contaminating the threadlocker.
Thread the shoulder bolt in by hand. The bottom face of the bolt shoulder must sit completely flush against the machined hinge mounting surface with no visible gap.
VDI recommends torquing shoulder bolt to 30 ft-lb (360 in-lb). This recommendation applies only to this specific shoulder bolt installed in the current VDI shock-mounting application with liquid red threadlocker.
Do not use pliers or other gripping tools on the shock body or shaft.
Do not scratch, paint, coat, or place foreign material on the shock body or shaft. Tool marks and surface contamination void applicable shock warranty coverage.
Critical shoulder-bolt seating requirement: The shoulder must contact the hinge mounting surface. Tightening the bolt head or reaching the torque setting does not confirm that the shoulder is seated correctly.
A visible gap leaves the narrow relief area between the shoulder and threads unsupported. Door movement can place a bending load directly on this area and cause the shoulder bolt to break.
Do not use the torque wrench to pull an unseated bolt into position. If the shoulder does not sit flush by hand, remove the bolt and inspect for cross-threading, debris, burrs, paint, incorrect hardware, misalignment, or threads bottoming inside the hole. Correct the cause before continuing.
Warranty notice: Damage caused by an improperly seated shoulder bolt, cross-threading, incorrect hardware, or failure to follow the required installation and torque procedure may not be covered under the applicable warranty.
Chevrolet Corvette C8 Vertical Door Conversion Kit
Upgrade your Chevrolet Corvette C8 with a vehicle-specific Vertical Doors, Inc. Vertical Door Conversion Kit, manufactured in the USA for proper fitment and reliable everyday operation.
Tag #verticaldoors and #lambodoors, and mention @verticaldoors when sharing your installation. We would love to feature your Corvette C8 on our website and social media.